Public announcement(JIS)
Public announcement(JIS)
This section is a public announcement to allow for the comment submission period (at least 60 days) and to collect information on related patents based on JIS patent policy, before establishment, revision and withdrawn of JIS. If there are any questions about the reported contents, related sections of the responsible organization are ready to deal with inquiries.
List of Public announcement(JIS)
| Standard number | Standard title | Establishment/ Revised | Organization | Comments deadline |
|---|---|---|---|---|
| B2711 | Springs-Shot peening（Amendment 1） | Revised | JSA | |
| C1910-1 | Measurement of DC magnetic， AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings - Part 1: Requirements for measuring instruments | Revised | JSA | |
| K6252-2 | Rubber， vulcanized or thermoplastic－Determination of tear strength－Part 2: Small (Delft) test pieces | Revised | JSA | |
| K6272 | Rubber－Tensile， flexural and compression test equipment (constant rate of traverse)－Specification | Revised | JSA |
1. "Degree of correspondence" with International Standards is indicated as follows, based on ISO/IEC Guide 21-1:2005 (Adoption of International Standards as regional or national standards).
IDT: "identical"
a)The regional or national standard is identical in technical content, structure*1) and wording*2), or b)the regional or national standard is identical in technical content and structure, although it may contain the minimal editorial changes such as misprints*3).
MOD: "modified"
Technical deviations, which are permitted, are clearly identified and explained. The regional or national standard reflects the structure of the International Standard, but changes in structure are permitted provided that the altered structure permits easy comparison of the content of the two standards.
NEQ: "not equivalent"
The regional or national standard is not equivalent to the International Standard in technical content and structure and any changes have not been clearly identified. No clear correspondence is obvious between the regional/national standard and the International Standard.
Note*1) "Structure" of the guide: Clause 3.10 (of a standard) order of the clauses, subclauses, paragraphs, tables, figures and annexes
Note*2) "Change in wording" of the guide: Clause 3.9When adopting an International Standard in one of its official languages, the replacement of single words or phrases in the regional or national standard by synonyms to reflect common language use in the region or country adopting the International Standard. Example: The use of "elevators" for "lifts" in certain countries.
Note*3) "Editorial change" of the guide: Clause 3.7 (of an International Standard in a regional or national standard) Any permitted change that does not alter the technical content of the standard.
Note: A list of permitted editorial changes is given in 4.2.
Clause 4.2 of the guide
- substitution of decimal point for a decimal comma
- correction of any misprints (e.g. spelling errors) or pagination changes
- deletion of text in one or several languages from a mustilingual International Standard
- inclusion of any technical corrigenda or amendments issued to the International Standard
- changes to the title to be consistent with an existing regional or national series
- "substitution of "this regional/national standard" for this International Standard"
- inclusion of any regional or national informative material(e.g. informative annexes that do not alter, add to or delete from the provisions of the International Standard). Examples of informative material are advice to users, training guidance or suggested forms or reports
- deletion of informative preliminary material from the International Standard
- changes in wording as defined in 3.9
- addition, for informative purposes, of recalculated values of quantity units where a different measurement system is used in an adopting country
2. The contents specified each standard will be indicated by the index number of International Classification for Standards ICS) which is specified by ISO. This index number is used also for the data exchange by WTO/TBT.
Inquiry and Contact
Japanese Standards Association
Mita Avanti, 3-11-28 Mita, Minato-ku, Tokyo, 108-0073, Japan
E-mail: sdcac@jsa.or.jp
